Suzuki Outboard Repair Manual Download

Suzuki Outboard Repair Manual Download Rating: 8,6/10 9084 reviews

SUZUKI DOWNLOAD 2006 2010 Service Manual DF150 DF175 150/175 HP Outboard; 2001 Suzuki GSX-R1300 Supplement Service Repair Manual DOWNLOAD; Suzuki outboard motor 2HP to 225HP service manual repair 1988-2003 DT; Suzuki Outboard DF90 100 115 140 4 Stroke Service Manual; MAZDA CAROL 1998-2001 SUZUKI K6A I3 ENGINE WORKSHOP MANUAL; 2001-2009 Suzuki. A downloadable Suzuki boat motor repair manual, also termed Suzuki outboard online factory service manual (FSM) or Suzuki engine workshop manual, is a digitally transmitted handbook giving instructions on how to overhaul, service or restore the motor back to working order.

Download a Suzuki 115 hp repair manual instantly. A Suzuki 115hp, termed DF115, is a book of repair instructions outlining every aspect of maintenance, troubleshooting and repair. The repair book appears identical to a book you’d obtain at your local marine shop. Do you own a Suzuki 115 hp outboard motor? Having the perfect tool.

I did not remove the rubberedge from the cowl panel, but instead applied a strip of 3/8' black foam tothe windshield under the edge of the rubber strip to keep it from contacting thewindshield. Either use 5/16' flat washers under the body panel screwsor trim the back off of the old plastic screw/clips and use the remainingportion as washers for the body panel screws. Also, the red plastic cover from thepositive battery terminal has been removed. On the larger cowl panel I slid a strip of felt between therubber strip and the windshield. Hbattery cover clips for 2004 rv4=utf-8#q=toyota+rav4+repair+manual+free+download&*. Note that 3/4' self adhesive foaminsulation tape has been applied to all locations on cross members and body panelscontacted by cowl.

RELATED SUZUKI OUTBOARD SEARCHES:

PROPELLERS

An outboard motor is designed to develop its rated power within a specified engine speed range. The maximum rated power delivered by the Suzuki models are shown in your service manual. If the standard propeller fails to meet the above requirement, use another pitch propeller to hold the engine speed within the range specified in your manual propeller selection chart.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.

Disassembly of propeller shaft components

1. Slide propeller shaft away from reverse gear housing assembly

Account for reverse gear back-up shim thrust washer

2. Remove horizontal slider and forward gear thrust washer

3. Remove spring

4. Using special tool, push dog pin shifter.

5. Remove clutch dog shifter propeller shaft.

Suzuki Outboard Parts

PROPELLER

• Inspect propeller for bent, chipped or broken blades and replace or repair if necessary.

• Inspect propeller bushing splines for wear or other damage and replace if necessary.

• Inspect propeller bushing for deterioration or slipping and replace if necessary.

PROPELLER SHAFT COMPONENTS

• Inspect horizontal slider and connector pin for excessive wear or other damage. Replace if necessary.

• Inspect clutch dog shifter for excessive wear, chip or other damage. Replace if necessary.

• Inspect dog pin for bent or other damage. Replace if necessary.

• Inspect propeller shaft / splines for wear, twist or other damage. Replace if necessary.

PROPELLER SHAFT BEARING HOUSING

• Inspect housing for cracks or other damage. Replace if necessary.

• Inspect propeller shaft bearings and reverse gear bearing for pitting, rough or other damage. Replace if necessary.

• Inspect oil seals and O-ring for cuts, nicks or tears.

Replacing propeller shaft oil seal

1. Remove retaining ring

2. Extract oil seals

1 and washer 2.3 using oil seal remover.

Do not re-use oil seal once removed.

Suzuki Outboard Repair Manual Free Download

Always use a new oil seal.

3. Apply Water Resistant Grease to inner circumference of housing.

4. Using an oil seal installer, drive two oil seals (one at a time) into housing.

The lipped portion of seal should face towards propeller.

Apply Water Resistant Grease to seal lips.

5. Install washer and retaining ring.

PROPELLER INSTALLATION

1. Install spacer shaft, then slide on propeller

2. Fit spacer specified torque.

Suzuki Outboard Repair Manual Download

1 and propeller stopper 2 onto propeller3.4, washer 5 and nut 6, then tighten nut to

Propeller nut : 55 N.m (5.5 kg-m, 40.0 lb.-ft.)

3. Push cotter pin secure.

PROPELLER SELECTION FOR COUNTER

ROTATION

Suzuki Outboard Repair Manual Download Free

For counter-rotation model, newly designed stainless steel propellers are available as follows.

Suzuki highly recommend to use the genuine Suzuki counterrotation propeller for the counter rotation model. In case of twin installation, always use on both engines, the same size normal rotation and counter-rotation propellers.

ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)

• Incorrect by-pass air screw adjustment [NOTE3]
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)